Why are nanocrystalline track cores set to replace traditional ferrites?

November 19, 2026

Laatste bedrijfsnieuws over Why are nanocrystalline track cores set to replace traditional ferrites?

New energy vehicle production and sales continue to climb, and the integration of photovoltaic, storage, and charging is accelerating. Automotive OBCs (on-board chargers), DC-DC modules, PV inverters, and charging piles form the core matrix of new energy power conversion. These devices are all moving in the same direction: higher power density, smaller size, and quieter operation. This trend is forcing upstream magnetic components to upgrade. Traditional ferrite cores are gradually reaching their physical limits in high-frequency, high-power scenarios, bringing nanocrystalline racetrack-type common-mode inductor cores to the forefront. SHINHOM's nanocrystalline racetrack cores are built around three major trends: wide temperature range, high saturation flux density, and low magnetostriction. The following analysis first examines the bottlenecks of traditional solutions, then the breakthrough points of nanocrystalline.

Why Can't Traditional Ferrite Keep Up?

Faced with the combined demands of high-voltage fast charging and compact space, traditional ferrite cores have three physical bottlenecks:

Bottleneck 1: Low Saturation Flux Density (Bs) – Size Cannot Be Reduced

  • Ferrite Bs is typically around 0.4T

  • Moving from 400V to 800V doubles the current

  • To prevent saturation, ferrite must multiply its cross-sectional area

  • The result is a larger core and a heavier inductor, violating the principle of lightweight design

  • Nanocrystalline Bs reaches 1.2T, nearly 3 times that of ferrite, handling greater current in the same volume

Bottleneck 2: Rapid Degradation at High Temperature – Prone to Thermal Runaway

  • When an automotive OBC or PV inverter is at full load, the cabin temperature easily exceeds 100°C

  • Ferrite Bs degrades significantly at high temperature, inductance drops sharply, and filtering fails

  • Nanocrystalline remains stable across the wide temperature range of -40°C to 150°C, with no degradation at high temperature

Bottleneck 3: Large Magnetostriction – Causing High-Frequency Whine

  • Ferrite deforms noticeably under an alternating magnetic field

  • Equipment emits a piercing high-frequency whine at certain frequencies

  • In a quiet cabin or an MRI environment, this NVH problem is critical

  • Nanocrystalline's magnetostriction coefficient is close to zero, eliminating mechanical vibration noise at the source

laatste bedrijfsnieuws over Why are nanocrystalline track cores set to replace traditional ferrites?  0

Stringent Requirements for Cores Driven by the Trends

Based on the bottlenecks above, the new energy market imposes three hard requirements on common-mode inductor cores:

Strong Anti-Saturation Capability: Meet the high-current demands of fast charging and high-voltage platforms.

Good Temperature Resistance and Structure: Adapt to extreme automotive temperatures and compact, low-profile spaces.

Quiet Operation: Meet the low-noise standards of automotive-grade and medical equipment.

The Breakthrough Points: How SHINHOM Nanocrystalline Racetrack Cores Precisely Match the Requirements

Breakthrough 1: Bs 1.2T High Saturation Flux Density – Supporting High-Voltage Fast Charging

  • In the same volume, DC bias resistance far exceeds that of ferrite

  • Three initial permeability grades for precise selection by operating condition:

    • 35k: high-current fast-charging main inductor (strongest anti-saturation)

    • 70k: balances impedance and bias

    • 105k: signal-level / low-current high-frequency filtering (highest impedance)

  • Performance tolerance controlled within ±10%, ensuring batch production consistency

Breakthrough 2: Wide Temperature Range and Racetrack Structure – Meeting Harsh Automotive Environments

  • Operating temperature covers -40°C to 150°C, with no degradation of magnetic performance at high temperature

  • Racetrack structure: compared with traditional toroids, better suited to low-profile designs

  • Adapts to the compact space of automotive OBCs and DC-DC modules

  • Multiple standard sizes available, with custom non-standard sizes supported

Breakthrough 3: Ultra-Low Magnetostriction – Achieving Quiet Operation

  • Magnetostriction coefficient close to zero, completely eliminating high-frequency whine

  • Meets the quiet cabin requirements of new energy vehicles

  • Adapts to the zero-tolerance noise standards of medical power supplies (MRI, ventilators)

Snapshots of Typical New Energy Operating Conditions

Snapshot 1: 800V Platform Automotive OBC

Under summer sun exposure, the engine compartment temperature approaches 120°C, and the fast-charging current is extremely high. Ordinary ferrite Bs drops sharply at this temperature and faces saturation risk. With 1.2T high Bs and 150°C temperature resistance, SHINHOM nanocrystalline cores reliably withstand high-current surges without increasing volume, and produce no high-frequency whine, ensuring fast-charging safety and a quiet driving experience.

Snapshot 2: Photovoltaic Inverter

Outdoor photovoltaic equipment endures long-term day-night temperature swings and full-load challenges. Nanocrystalline cores maintain high impedance characteristics across the full -40°C to 150°C temperature range, suppressing high-frequency EMI and ensuring the inverter remains stably grid-connected over the long term in harsh climates.

laatste bedrijfsnieuws over Why are nanocrystalline track cores set to replace traditional ferrites?  1

Application Scenario Suitability

Application Scenario Pain Points of Traditional Solutions SHINHOM Nanocrystalline Corresponding Capabilities
Automotive OBC / DC-DC modules High-temperature saturation, large size, whine Bs 1.2T anti-saturation; -40~150°C wide temperature; racetrack compact structure; ultra-low magnetostriction
PV / wind power inverters Large outdoor temperature swings, long-term operational degradation Bs 1.2T high saturation flux density; full-temperature-range stability
New energy charging piles Fast-charging high current prone to saturation, high-frequency interference Three permeability grades (35k recommended for anti-saturation); high saturation flux density
Medical power supplies (MRI/ventilators) Extremely strict noise requirements, high reliability requirements Ultra-low magnetostriction (near-zero noise); ±10% tolerance control

Conclusion

The electrification of vehicles and the explosive growth of new energy are, in essence, an extreme squeeze on power conversion efficiency and power density. The ferrite era is giving way to the nanocrystalline era.

SHINHOM nanocrystalline racetrack cores respond to market trends with three major characteristics:

  • Bs 1.2T high saturation flux density: In the same volume, anti-saturation capability is nearly 3 times that of ferrite.

  • -40°C to 150°C wide temperature range and racetrack structure: Unfazed by automotive high temperatures, adapted to compact low-profile designs.

  • Ultra-low magnetostriction and three permeability grades (35,000 / 70,000 / 105,000): Completely eliminate whine, enabling precise selection for different power levels.

The products already cover automotive OBC, DC-DC, EPS, as well as PV, wind power, charging piles, and medical power supplies.

📧 Email: sales@shinhom.com

🌐 Website: www.shinhom.com/

Neem contact op met ons
Contactpersoon : Jack wang
Tel. : 13909218465
Fax : 86-029-87851840
Resterend aantal tekens(20/3000)